• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Your first line of defense is your door lock replacement upvc door. It will stop unauthorized access to your home. Locks may need to be replaced due to signs of wear and tear or other events like moving into a new home or a break-in.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will assist you buy the lock that is right for you.

Deadbolt

Installing a deadbolt is ideal way to secure your door against intruders. The bolt extends into the strike plate on the door frame when it's locked, making it much more difficult for a burglar to gain entry into the door. A single-cylinder deadbolt can be activated with a key on the outside and a thumb-turn piece situated inside. Deadbolts are only effective if it's installed correctly, though.

First, you'll need to find out if the door has a hole to install a deadbolt or if it needs to be bored out. Using the template that comes with your lock installation kit, mark the spot of the deadbolt's hole on the door's surface. Utilize your tape measure to determine the height of the deadbolt. Then, mark this high point on the outside of the door. Use the speed square to draw a straight line across the mark you made for the bolt hole.

Then by using a power drill, bore out the hole until it is on the opposite side of the door. It could take a few minutes. Sand the hole and the door edge to make it smooth. At this point, it's a good idea also to stain or paint your door.

Remove any visible screws from the deadbolt. This will reveal the front door lock replacement cost (Full Piece of writing) and back assembly of the deadbolt and also the bolt inside. Remove the bolt and replace upvc door lock mechanism it with the new bolt to match the door hardware. You'll need to remove the bolt from a setplate. After this is done then you need to chisel out the area for the strike plate that is on the door frame.

If your strike plate is misaligned, it's likely because the previous installer didn't properly mortise it or a weatherstripping popped up and changed the strike's position. You'll need to re-mortise your strike plate and perhaps even the deadbolt to correct this problem. Once you have completed this check the deadbolt by closing and locking it. Make sure that the bolt extends into the strike plate and composite door replacement lock then test the key to ensure it closes and opens smoothly.

Knob

If a door knob is worn out it could make your home or business less secure. It can also make opening and closing the door more difficult, which is why it's a good idea for you to replace it. It shouldn't take more than 30 minutes. You can use a screwdriver as well as pliers to take off the knob or handle that was previously used Be careful not to harm any of the other components on the door.

Before starting, you'll want to spray WD-40 or some other dry lubricant on the mechanism of the knob on your door. This will let the lock to move effortlessly when you turn it. To ensure proper operation it is important to select the knob and handle that match your existing doors. If you don't have a doorknob that matches then you'll have to purchase a replacement locks for patio doors.

To begin the replacement process, first examine the old knob or handle to find what screws hold it in place. If there aren't any screws you can use a screwdriver to wedge between the cover plate and the plate with hidden screws and pop it off.

After you've removed your old knob, examine it for signs of damage or rust. If the knob is damaged or has marks or scratches then you'll need clean it. Otherwise, it shouldn't require any major work.

Install the new knob. It is important to first look over the two knobs in order to make sure that you've selected the right one for the door. You'll need to choose one with an extended rod that is interlocked with the rod mechanism of the other knob. After you've placed the new knob over the hole in the door and then carefully slide it into the latch.

Test the spring by pressing down on it repeatedly. The latch should rise each time. Then, put in the new knob and lock it with the rod mechanism on the previous knob. Then, thread the other long screws from the knob's interior through the hole for the cylinder on the doorknob outside and secure it.

Latch

A latch is a piece of metal that extends into the doorjamb to hold it shut. The latch is operated via a knob or handle located inside the door, or by a thumb-turn on the exterior. A latch can be secured with deadbolts to stop intruders from breaking in through the upvc door locking mechanism replacement's glass. It also provides protection from accidental or intentional closing of the door by pets or children. The latch can be fitted with a single cylinder deadbolt or double cylinder deadbolts, according to the security level you prefer.

Installing a latch follows the same steps as installing a deadbolt, however, there are a few differences. First, determine the setback of the doorjamb with a tape measure to make sure that the new lock will fit. The setback is the distance between the edge of the doorjamb to the middle of the hole to accommodate the latch faceplate. A standard setback is 2 3/8 to 2 3/4 inches. If you have a larger setback, you may have to purchase a larger latch at a hardware store or locksmith.

Then, you'll need to make a hole for a latch plate in the edge of the doorjamb. Use a chisel for chiseling out the latch mortise, making sure it's deep enough for the faceplate of the new latch to sit flush with the doorjamb. Tape the strikeplate in place to ensure it's placed correctly.

If the strike is set too high, the door can be kicked in or pressure imposed on it using a crowbar or tire iron. This could also cause cracks in the doorjamb. To fix this, the strike could be reduced by drilling a second hole into the doorjamb and chiseling out the center of the hole that was previously drilled.

The last step is to put in the new strike plate, which is done by screwing it over the screw holes that are already in place. Then apply wood putty to cover the screw holes that were previously used and the bolt hole that is not used. When the putty is dry, sand it smooth for professional results.

Strike

The piece of metal that is inserted between the latch and deadbolt when the door is closed is an electric strike. It is a vital component of a lock's overall security, because it helps keep the door shut and provides extra resistance to force or kicks applied to the door. If a door is equipped with an electronic strike, it can be opened only with keys and the control unit that controls its electrical impulses.

In the past, installing an electronic strike required cutting a piece of a doorjamb, which would let the latchbolt of a cylindrical lock from the pocket within the strike. This modification is not just unattractive, but also exposes the mechanism for the latchbolt and keeper to uninitiated users.

Recently, a number of electric strike manufacturers have come up with a "No Cut" kind of strike that does not require a cutout to operate. These strikes utilize a special design that allows the latchbolt and keeper to slide into the strike pocket without marring the doorjamb faceplate.

The strike is fitted with an internal ramp that raises the latchbolt as well as the keeper when it receives the signal of a reader. The latchbolt and keeper are pushed on the ramp thanks to the retract. When the door is closed the deadbolt is retracted and the latchbolt retracts in the keeper.

Installing an electronic strike is a straightforward process, particularly in the case of replacing an existing strike. If you're upgrading an existing access control system to an electric strike, it is important to make sure that the new system is compatible. It is also necessary to make sure that the strike is properly wired to your access control system and is set up for fail-safe operation.

Upgrade your strike plates to heavy duty strike plates to block unauthorised entry. These plates can be fitted with up to six screws of three inches instead of two screws of three-fourths of an inch. These screws are longer, making it harder for people to break the frame and then reach inside to turn the thumb turn piece of a single deadbolt cylinder.